收藏本站
NCP5050
PIN FUNCTION DESCRIPTION
Pin
Pin
1
2
3
4
5
6
7
8
9
10
Name
PGND
VS
CTRL
CM
PCA
HCS
FB
LCS
PVIN
SW
Type
POWER
INPUT
INPUT
INPUT
INPUT
INPUT
INPUT
INPUT
POWER
INPUT
Description
Power Ground : This pin is the power ground and carries the high switching current. A high quality
ground must be provided to avoid any noise spikes/uncontrolled operation. Cares must be observed to
avoid high ? density current flow in a limited PCB copper track.
Voltage Sense : In order to sense V out notably for over voltage protection, this input must be
connected to the output bypass capacitor C out .
Control and Enable : An active high logic level on this pin enables the device. A built ? in pulldown
resistor disables the device if the pin is left open. Also in disable condition the device provide a true
cut ? off thank to the high impedance on FB input. This pin can also be used to control the average
current into the load by applying a low frequency PWM signal. If a PWM signal is applied, the
frequency should be high enough to avoid optical flicker but be no greater than 50 kHz.
Current Mode : An active high logic on this input enables the High Current Sense used for flash and
disables the LCS resistor. This pin has a low voltage threshold so it can be driven directly from 1.8 V
logic signals. If this function is not needed, this pin should be grounded. Only when CM pin is high, a
safety function switch off the output if CTRL pin is high longer than 1.2 s
Peak Current Adjust : A resistor between this input and ground controls the maximum peak current
allowed in the inductor. The minimum value for this resistor is 2.8 k W and increasing this value
decreases the peak current. This allows the user to adjust the current based on the application needs
and scale the size of the inductor accordingly. See “Switch Current Limit” guidelines in application
section.
High Current Sense : This pin is used for Flash Mode. If the user desires two levels of LED current
then a resistor should be connected from this pin to ground. This function is controlled by the CM input.
Feedback : The reference is 250 mV. This pin provides the feedback voltage by means of the sense
resistors fixed by LCS or HCS pin. When the device is enables and CM low, the LCS resistor is
connected to this pin, thereby the LCS setup the LED current. The tolerance of the LED current is
dependant upon the accuracy of this sense resistor and a $ 1% metal film resistor, or better, is
recommended for best output accuracy.
Low Current Sense : This pin is used for Torch Mode. In order to fix the current when CM logic pin is
low, a resistor should be connected from this pin to ground.
Power Supply : The external voltage supply is connected to this pin. A 4.7 m F / 6.3 V high quality
capacitor must be connected across this pin and the power ground to achieve the specified output
power parameters. The X5R low D C/C versus DC bias ceramic types are highly recommended.
Switch : Power switch connection for inductor. Typical application will use a coil from 2.2 m H ? 4.7 m H
and must be capable of handling the peak current.
http://onsemi.com
3
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
NCP5111DR2G IC DRIVER HI/LOW SIDE HV 8-SOIC
NCP5304DR2G IC DRIVER HI/LOW SIDE HV 8-SOIC
NCP5355DG IC DRVR SYNC BUCK MOSF 12A 8SOIC
NCP5359ADR2G IC MOSFET GATE DVR DUAL 8-SOIC
NCP5359DR2G IC GATE DRIVER VR11.1/AMD 8-SOIC
NCP5360RMNR2G IC DRIVER MOSFET 56QFN
NCP5366MNR2G IC DRIVER MOSFET DFN
NCP5369MNR2G IC DRIVER MOSFET DFN
相关代理商/技术参数
NCP508 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Very Low Noise, Fast Turn On, 50 mA Low Dropout Voltage Regulator
NCP5080 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Xenon Photoflash Capacitor Charge with Photo Sense Interface
NCP5080 AX95A WAF 制造商:ON Semiconductor 功能描述:
NCP5080MUTXG 功能描述:LED照明驱动器 HI VLTG BOOST DVR 2.7-5.5V RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
NCP508MN15TBG 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Very Low Noise, Fast Turn On, 50 mA Low Dropout Voltage Regulator
NCP508MN18TBG 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Very Low Noise, Fast Turn On, 50 mA Low Dropout Voltage Regulator
NCP508MN25TBG 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Very Low Noise, Fast Turn On, 50 mA Low Dropout Voltage Regulator
NCP508MN28TBG 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Very Low Noise, Fast Turn On, 50 mA Low Dropout Voltage Regulator